Tips To Install A New Garden Gate

Tips To Install A New Garden Gate

Do you need to install a new garden gate, fence, or wall? If so, you have come to the right place. This article from Gates and Automation Direct provides tips to set up and finish the project without any long-term issues.

First, you need to set up the entryway and posts and assemble the fence from there. If you plan to use an old door, make sure to check the measurements precisely to make sure you have the correct size. Don’t forget to take a measuring tape with you when purchasing the new entryway since they are usually sold in both metric & magnificent sizes and the changes are not precise at times. The next thing is to consider which way you want the entryway to open. For example, most entryways open into the property instead of out.

Apparatuses & Materials Required


Gate Posts designed for light entryways are around 100mm square and 610mm longer than the stature of the door. For gates that are more than 1.2m wide or high, the posts should be thicker – no less than 760mm longer than the tallness of the entryway. You should always check the manufacturer’s particulars. Wooden gate posts should be treated with glue or something similar, and they should be set in concrete since the post spikes are not stable enough to make sure the gate structure will be strong under stressful circumstances. If possible, you should opt for fittings that have been lacquered or electrified to prevent them from rusting.

Top Tip – Adjusting The Pivots

If you notice there’s some “play” when you try to screw the pivots to the entryway, you should modify them after setting the posts. If not, it will be difficult to position them precisely. In order to make things easier, you should fit only two holding screws for each pivot into the post while they are at lying level. In fact, you should hold on until you have hung the entryway before fitting the hook.

Stage 1

In case your entryway posts are not weathered, you should slice them to an inclination so water will keep running off. In fact, you should try to do this in the first place by using a sliding slant to check a 20-degree point from the highest point of the post.

Stage 2

The next step is to proceed with the line straight down the substance of the entryway post and saw along it. At that particular point, paint the cut edge with a wood additive. If the wood is untreated, you may have to paint the entire post.

Stage 3

Once you choose which way you need the entryway to open, lay it facing downward on level ground. Place the posts with their tops at least 50mm higher than the highest point of the entry door and leave a 5mm hole on either side of the entryway. This is important for the door to close and open unreservedly. Don’t forget to use 2 timber lengths in order to marginally raise the entryway so that it sits level with the gateposts. You can opt to change this with timber wedges or off-cuts.

Stage 4

Now, place the pivots into position on the back of the entryway. Bore one pilot gap and stamp the screw positions. In order to check that the bore is not too expansive, you should test it by driving in a screw. At this point, bore the rest of the pilot openings.

Stage 5

The next step is to fasten the pivots put using galvanized screws. If you are doubtful of positioning them precisely on the post, don’t fit them or the lock until you have hung the entryway.

Stage 6

Bore pilot openings to position the hook screws & screw the lock into put. You should leave a 5mm hole between the door & post while doing so.

Stage 7

Now you need to support the posts and door with at least three lengths of timber to make sure they are strong. Use the propped entryway to stamp the position of the post openings.

Stage 8

Use a post-gap borer or a spade to burrow the opening of the post. Leave a 50mm leeway hole beneath the door so it can open unreservedly. Check if this is enough by laying a soul level on the ground where the entryway is supposed to open and level the ground if you have to. If the ground is too delicate, you may have to burrow a trench between the post gaps – approximately 200mm profound and 300mm wide and fill it in with concrete.

It helps prevent the posts from being pulled inwards due to the heaviness of the door. Use a spirit level to check that they are in line and then lower the gate-posts into the openings.

Stage 9

Use timber props in order to hold the posts and door in the correct position. Mix the concrete and set the posts into the ground. Slant the surface downwards so that it can coordinate water far from the wood.

Stage 10

Don’t forget to let the concrete mix set for 48 hours before you decide to evacuate the support and props.

Read More: Benefits of New Gates